The
Monolith Version 2 is a high-performance 3-way loudspeaker that excels
in both sonic quality and application flexibility. Its unique
flat-profile design enables it to perform in a variety of applications
with unparalleled results. For some applications the compact cabinet
size alone makes it attractive, but the Monolith Version 2’s most
important characteristic is its sound. Located inside the 8.5-inch deep
cabinet are an 18-inch woofer, two 6.5-inch direct-radiating
mid-frequency drivers, and a 2-inch high-frequency compression driver
coupled to a slot-CD horn. These components work together to provide
true broadband response which is effective from 17kHz to below 50Hz. The
carefully selected components provide significant LF output, along with
excellent clarity and sonic detail in the MF and HF ranges. The standard
Monolith Version 2 is a bi-amplified design, with tri-amp available as
an option.
The Monolith Version
2 builds on the strengths of the original Monolith, adding significant
improvement to its audio performance. Long considered one of the
best-sounding loudspeakers on the market, the Monolith Version 2 raises
the "sonic bar" with flatter response, better phase coherence,
and increased detail. Significant improvements were made to both the MF
and HF sections of the loudspeaker. A new MF driver was selected, of
which two are used in each Monolith Version 2. The new driver features a
composite cone and an integrated phase plug. A new crossover network was
designed to optimize MF performance. A custom-designed damping insert is
now incorporated into the HF compression driver. This reduces the
standing waves that can be created by the driver’s rear mechanical
system. A re-designed HF crossover network effectively shapes and
controls the response of the compression driver. The MF and HF sections
work together to provide a nominally flat response with minimal phase
interaction. Listeners will experience excellent clarity and strong
inter-sonic detail.
Monolith
Version 2 loudspeakers can effectively be used singly, in stereo pairs,
or in multi-cabinet vertical line arrays. For application flexibility,
the MF and HF components can be rotated. This is especially important
when creating vertical line arrays, proving high sound-pressure levels
and wide coverage without the phase anomalies typical in horizontally
arrayed system. Versions are available for portable or installation use.
Both include provisions for overhead-suspension use, incorporating
aluminum aircraft track and threaded insert points. Rigging components,
including a low-profile fly bar and cabinet-to-cabinet fittings, are
available. For portable applications the road version includes the
Intermast System, a proprietary design which incorporates mounting poles
and hardware inside the loudspeaker’s cabinet. This unique feature
allows direct cabinet support using subwoofers, the factory-available
road case, or floor stands. When not in use, the Intermast System
retracts completely into the cabinet.
The Monolith Version
2’s cabinet is made of hardwood plywood with a powder-coated steel
grill. The sleek cabinet design minimizes disruption of sight lines. The
road version includes textured epoxy paint and plastic-laminate
protection panels on the left and right sides. The install version uses
a low-gloss, light-texture paint finish that is optimized for permanent
installations.
Monolith Version 2
Specifications
Standard
Configurations:
MONO-RD-V2: Road version
MONO-IN-V2: Install version
MONO-IN-IM-V2: Install version with Intermast
MONO-RD-SET-V2: Two road versions in case
Above versions also available in tri-amp
Frequency
Response:
±3 dB, 44 Hz to 17 kHz
Coverage
(between –6 dB points):
Horizontal: 90 degrees
Vertical: 55 degrees
Components rotate for pattern control and correct alignment within the
array
Nominal
Impedance:
LF: 8 ohms
MF/HF: 6 ohms
Sensitivity:
LF: 96 dB
MF: 102 dB
HF: 106 dB
Maximum
SPL:
124 dB, broadband, one meter, one minute
Recommended
Amplifier Power:
LF: 500 to 750 watts RMS into 8 ohms
MF/HF: 350 to 500 watts RMS into 6 ohms
Recommended
Crossover Point:
240 Hz, 24 dB per octave
Maximum
Input:
LF: 750 watts
MF/HF: 500 watts
Connectors:
2, Neutrik NL4
Enclosure:
SBABS plastic laminate (on sides only) on hardwood plywood, textured black or paint-ready finish,
powder-coated perforated steel grill with
open-cell foam backing
Dimensions:
43.3 inches high (110.0 cm)
22.4 inches wide (56.9 cm)
8.5 inches deep (21.6 cm)
Weight:
128.0 pounds (58.1 kg): Road version
116.0 pounds (52.6 kg): Install version
123.0 pounds (55.8 kg): Install version with Intermast
378.0 pounds (171.5 kg): Two road versions in case
Accessories:
flybar, loop-to-fitting strap,
fitting-to-fitting link strap ("short"), fitting-to-fitting link strap ("long"),
fly hinge, cloth cover
Options:
road case
cover
Warranty:
three years from date of original purchase
Contents subject to change without notice.
Dimensions provided for general reference only.
